Sinotruck CZPT 4×2 mini 2000 gallon water truck for sale
Sinotruck CZPT 4×2 mini 2000 gallon water truck for sale
|LHD (RHD is optional)
|HW76, with 1 sleeper and 2 seats, double arm windscreen wiper system with
three speeds, damped adjustable driver’s seat, with heating and ventilating system,
exterior sun visor, safety belts, adjustable steering wheel, air horn, air conditioner,
with transverse stabilizer, with 4 piont support floating suspension+shock absorber.
Diesel 4-stroke direct injection diesel engine
Engine model: WD615.47, Euro 2, 371 HP
6-cylinder in-line with water cooling, turbo-charging and intercooling
Displacement: 9.726 L
|HW19710, 10F & 2R, with PTO
Ratio:14.28, 10.62, 7.87, 5.88, 4.38, 3.27, 2.43, 1.80, 1.34, 1.00, 13.91(R1), 3.18(R2)
|ZF power steering, modol ZF8118, hydraulic steering with power assitance
Steering with doubleT-cross section beam
|HC16, 2×16000 KGS
Pressed axle housing, central single reduction with hub reduction,with differential
locks between wheels and axles.
|Double universal joint propeller shaft with gear-shaped coupling flange
|Frame: Uprofile parallel ladder frame with section of 300x80x8mm,reinforced
subframe all cold riveted cross members Front suspension:10 semi elliptic leaf
spring, hydraulic telescopic double-action shock absorbers and stabilizer
Rear suspension:12 leaf semi elliptic springs, bogie spring and stabilizer
|Service brake: dual circuit compressed air brake
Parking brake (emergency brake): spring energy, compressed air operating on
front shaft and rear wheels
Auxiliary brake: engine exhaust brake
|Operating voltage: 24 V, negative grounded
Starter: 24 V, 5.4 Kw
Alternator: 3-phase, 28 V, 1500 W
Batteries: 2 x 12 V, 165 Ah
Cigar-lighter, horn, headlamps, fog lights, brake lights, indicators and reverse light
|295/80R22.5,12R22.5 tubeless tyres with 1 spare tyre
|Oil Tank Body
|20 Cubic Meters, with front and rear sprinkling system.
1. Dump Truck / Tipper Truck
2. CZPT tractor Truck/ prime mover truck
3. Truck with crane / Truck mounted crane
4. Oil Tank Truck / Fuel Tanker Truck
5. Water truck / Water Tank Truck / Water Sprinkler Truck
6. Concrete Mixer Truck
7. Van truck / Insulated truck/ Refrigeration truck
8. Fecal suction truck / Sewage suction truck
9. Cement Powder Tank truck/ Bulk cement trailer
10. High-altitude operation truck
11.Semi Trailer ( flat bed trailer / skeleton trailer / dump trailer / side wall trailer / low bed trailer / container trailer, etc. )
Packaging & Shipping
Shipping method for Sinotruck CZPT 4×2 mini 2000 gallon water truck for sale :
Usually Our Truck can be shipped by Ro-ro ship or Bulk ship or Container or Flat rack.
Packing Detail: Ro-Ro or Bulk base on the ship and port in your country. If the truck on the deck,we will spray antirust paint with free.
1. Q: What’s your MOQ?
A: One unit trailer or truck.
2. Q: What is your lead time?
A: Usually it is 15-20 days after deposit received.
3. Q: What is the warranty of the trucks?
A: 12 months about engine, axle and transimission, some spare part can be 18 months. And we can help you solve
every problem about the truck by email and phone whole life.
4. Q: What’s your payment terms?
A: T/T: 30% deposit by T/T,70% balance should be paid before shipment.
L/C: 100% irrevocable Credit of Letter.
5. Q:If Our Vehicle/Trailer Can Couple With Your Tractor Head ?
A:You can tell me that you are using the Tractor/Primer Mover model or the distance between fifth wheel and the ground,
we can design a height that matches your Tractor.
6. Q:If We Can Provide Terms For Reducing Your Import Duties ?
A:Yes, Please Contact With Us, We Are Nationalized Manufacture With Tax Reduction, Will Also Offer You The Best Way
For Import Duty Reduction.
7. Q: How about the after sales service?
A: We provide technical support and spare parts for long life time of our products.
|Techinical&Spare Parts Support
|15001 – 30000L
|12 – 16m
Choosing the Right PTO Shaft
There are several different types of PTO shaft. These include the Transmission PTO, the Economy PTO, the Type 4″ pto shaft, and the Two-stage clutch pto shaft. It is important to choose the correct one to ensure a smooth operation. When choosing a PTO shaft, consider the characteristics and uses of each type.
If you have been experiencing trouble with your Transmission PTO shaft, you may want to take it to a mechanic to have it looked at. A PTO problem can be frustrating and costly to fix. Here are some tips for resolving PTO problems. Start by checking your transmission oil and air pressure levels. Also, check for cracked or kinked hoses and screens. If none of these steps resolve the issue, you may need to replace your PTO.
There are two types of Transmission PTO shafts, Type 1 and Type 2. The first type was designed to be used for 540 rpm applications. Later versions were designed to handle higher PTO powers, and the diameter was changed to increase its speed. Both types have different diameters, so be sure to check the spline count.
Transmission PTOs are commonly used between tractors and farm equipment. These PTOs have the feature of a universal transmission, although the input and output ends are not always on the same plane. The drive shaft is also able to vary the angle between input and output ends. This allows the drive shaft to operate within a specified left and right expansion range.
When replacing a transmission PTO, make sure you check the shaft’s speed and backlash before installing it. In addition, check the transmission gears to ensure they are in good condition. Experts from suppliers recommend inspecting and replacing any debris on the gaskets. They also recommend setting backlash units between the transmission and PTO. In general, backlash units should range from 6,000 to 12,000 units.
To maintain the efficiency of your Transmission PTO, it is necessary to maintain the proper oil level. Make sure you regularly check the PTO fluid and filter. A change of fluid and filter is recommended every 75,000 miles and 300,000 miles. Using a dial indicator can help you to check backlash and prevent damage to the PTO or mating gear.
The Economy PTO shaft allows you to reduce the engine speed when driving your PTO. This mode uses different gears to adjust the PTO shaft revs. The cab-mounted control/monitoring unit 14 uses the PTO speed information to set the parameters of the PTO. In order to operate this system, you must be aware of the lever 21 position and the type of shaft fitted.
The ratio of the input shaft 7 and the output shaft 22 determines the precise value. The ratio also depends on the type of PTO shaft and the ratio of the gearbox. There are two different types of PTO shafts, and each has different toothed wheels. To choose the right one, you should know the ratio of the shaft and the gearbox.
A Domestic PTO shaft is the most common type used in North America. It comes in a wide range of diameters and splines and can be used on a variety of applications. It is durable and is resistant to pressure, impacts, and tension. It is also equipped with a shear pin and slip clutch to protect the PTO from common obstacles.
An Economy PTO shaft enables your tractor to run at lower rpms, reducing noise and vibrations. It is perfect for a variety of agricultural equipment and is controlled by your tractor’s transmission. It is available in two types: mechanical and hydraulic. A mechanical version has a clutch, while a hydraulic version has a lever to control the torque.
The Economy PTO shaft allows you to reduce fuel costs and increase productivity by up to 2%. It also reduces noise in the cab, which is a plus. Its auto-mode feature helps you operate the Economy PTO with ease. This system can also be programmed to automatically disengage the PTO when the linkage is raised.
Two-stage clutch on pto shaft
If you’re looking to get the most out of your tractor, you should check the clutch for two-stage operation. Two-stage clutches use two separate stages to disengage the PTO and gears. If the clutch does not disengage when you push the pedal, you’ll need to adjust it. Rust buildup can cause the clutch to stick and require a rebuild or replacement. Fortunately, there are many ways to check whether your clutch is slipping.
A two-stage clutch is commonly used in transmissions with live PTOs. The first stage operates the driven portion of the transmission, while the second stage controls the PTO. This arrangement allows the PTO to work independently of the transmission, which is especially useful in tractors that use mower attachments.
This two-stage clutch is usually accompanied by a gearbox. The gears in the PTO shaft are set up to rotate at a rate of 540 revolutions per minute (rpm) when the engine is running. The second clutch is designed to operate at a higher speed and can be used with different power sources.
A two-stage clutch on the PTO shaft is a good option if you’re using a tractor that doesn’t have a slip clutch. It will limit the tractor’s torque, so you’ll save money on fuel while doing work. It also helps reduce noise and vibration.
Types of independent pto shafts
Independent PTO shafts come with their own clutch, which enables them to run independently from the tractor’s transmission. There are two main types of independent PTO shafts: mechanical and hydraulic. The mechanical version has a separate on-off selector and control lever. The hydraulic version only has a single selector.
These different types of PTO shafts are only compatible with specific implements. The speed at which they transfer energy is different, too, and some are faster than others. This is why some large tractors have higher-speed PTOs than smaller tractors. A transmission PTO requires a parking break, while an independent PTO does not.
A newer type of independent PTO shaft, the Type 4, is also available. This model runs at a higher rotational speed, around 1300 rpm, which allows for a more efficient transfer of power. In addition, the Type 4 shaft is larger, with 22 splines and a diameter of 57.5 mm. It is designed to support PTO powers of up to 450 kW or 600 horsepower.
Another type is called a “sandwich” type, which is mounted between the transmission and engine. It receives its drive from the engine shaft. This type can transfer the full power of the engine to the PTO, although it needs modifications to the driveline. It also comes with its own lubrication system.
Independent PTO shafts can be manually operated or electronically controlled. The independent PTO is easy to engage and is often operated by shifting the PTO selector lever away from the ‘OFF’ position or by flipping the PTO switch to the “ON” position. Independent PTO shafts may also feature an additional manual clutch. This clutch helps regulate heavy loads and protects the PTO drive system.
editor by CX 2023-04-21